We may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Read our affiliate disclosure.
Short answer
If you want to read the code yourself, our pick is the BlueDriver OBD2 Scanner. See the BlueDriver OBD2 Scanner at Amazon.
A P0455 code means your car’s evaporative emission (EVAP) system has found what it reads as a large leak. GM’s bulletin says the code can also set from a “purge blockage.” During its self-test, the system tried to seal the fuel tank and vapor lines and build a target vacuum or pressure, and it never got there.
The short answer: the most common cause of a P0455 code is a loose or missing gas cap. Check the cap first, then drive normally for a few days so the system can retest itself. If the code comes back, a shop smoke test is the reliable next step, rather than buying valves on a guess. It’s usually OK to drive short term if there’s no fuel smell. A strong fuel smell or a visible leak needs immediate attention, Identifix warns, because fuel vapor near an ignition source poses a fire risk, so don’t keep driving on it.
Jump to: What it means · Vs. P0442 · Is it safe to drive? · How to fix it · A scanner · FAQ
What does the P0455 code mean?
P0455: Evaporative Emission System Leak Detected (large leak). You’ll also see it called a “gross leak.” Identifix calls it “Evaporative Emission System Leak Detected (Gross Leak),” RepairPal “Evaporative System Malfunction, Gross Leak,” and GM’s bulletin “Evaporative Emission System Large Leak Detected.” (The original SAE J2012 text is paywalled.)
Identifix explains that the engine computer tries to seal the system and pull it to a target vacuum or pressure, but “the reading never reached the target.” RepairPal says the system “cannot create enough vacuum pressure in the system, which is typically caused by an air leak.”
How P0455 differs from P0442
| P0442 (small leak) | P0455 (large leak) | |
|---|---|---|
| What the test saw | Vacuum built, then decayed too fast (RepairPal) | Vacuum or pressure never reached the target, or bled off almost at once (Identifix) |
| Typical size | About 0.040 inch (Identifix) | Larger than 0.040 inch, or no seal at all (Identifix) |
| Most common find | An aging cap seal, a small hose crack, a canister seam | A missing or loose cap, a valve stuck open, a disconnected line (Identifix) |
| GM’s take (bulletin 21-NA-124) | A stuck-open purge or vent valve, or an unsealed system | A large leak or purge blockage: an unseated or damaged tube, a vent valve stuck open, or a purge valve stuck closed |
| Severity (RepairPal) | Moderate | Moderate |
The very small leak code is P0456, about 0.020 inch, the size federal rules require OBD systems to detect (40 CFR 86.1806-17). For the small-leak version, see our P0442 guide.
Is it safe to drive with a P0455 code?
- Usually, yes, short term, if there’s no fuel smell or leak. RepairPal rates it “Moderate” and says it “might not threaten the vehicle’s safety or functionality immediately.”
- Not if you smell fuel or see a leak. Identifix says a strong fuel smell or a visible fuel leak needs “immediate attention,” and that “fuel vapor near an ignition source poses a fire risk.” Don’t keep driving on it. If it happens on the road, pull over somewhere safe and turn the engine off: Kia’s fuel-leak recall notice, hosted by NHTSA, says “If fuel smell and/or leakage is detected, immediately TURN OFF your engine, and do not drive your vehicle.” Keep sparks, flames and cigarettes away, and have the car towed for repair.
- It can fail inspection. In states with OBD emissions testing, a lit check engine light usually means a failed inspection. Clearing the code doesn’t fix anything, and it resets the readiness monitors. North Carolina’s DEQ rejects a car as “Not Ready” if more than two monitors are incomplete on a 1996–2000 model, or more than one on a 2001 or newer model, so you’d need to drive it until they finish. Other states set their own rules.
For what solid and flashing lights mean, see check engine light on? what it means and what to do.
Symptoms
- A check engine light, often the only symptom. RepairPal: “In most cases, there are no adverse conditions noticed by the driver.”
- A fuel smell, “caused by the release of fuel vapors” (RepairPal). Identifix says a smell inside the cabin means vapor is getting into the car and is a fire risk.
- Trouble refueling, with the pump nozzle clicking off. Identifix says that points to the vent path or the canister.
- Rarely, a rough idle if a purge valve is stuck open, sometimes with a P0171 lean code (Identifix).
What causes a P0455 code?
- A missing, loose, damaged or wrong gas cap. Identifix calls a loose cap after refueling “the single most common cause,” and warns that aftermarket caps with the wrong seal profile can leak “while looking perfectly fine.”
- Cracked or disconnected EVAP hoses, including plastic quick-connects that are seated but not locked (Identifix). GM’s bulletin lists “an unseated tube connection, a damaged tube.”
- A vent valve stuck open or a purge valve stuck (GM 21-NA-124; Identifix; RepairPal).
- A damaged charcoal canister: a cracked housing, split seams, or saturation from repeated overfilling (Identifix).
- A leak at the fuel tank or filler neck: a rusted filler neck in salt-belt states, a tank seam, or the fuel pump module seal (Identifix; RepairPal).
- A faulty fuel tank pressure sensor (RepairPal). Identifix says F-150 tank pressure sensors can fail intermittently and set the code with no physical leak.
RepairPal’s note on misdiagnosis: “Missing or loose fuel cap is easy to check and replace, but the problem may be deeper,” followed by the purge and vent valves.
Common by make (per Identifix)
- GM trucks: road grime packs the vent solenoid. On the Cruze, Malibu and Equinox, purge solenoids can stick open.
- Ford: on capless “Easy Fuel” fillers (F-150, Escape, Focus, Explorer), the flap is the first place to look. Use the funnel adapter that came with the car for a smoke test.
- Hyundai and Kia: the canister close (vent) valve can stick.
These are patterns Identifix reports, not factory documents, and they don’t mean every one of those cars has the problem.
Known factory guidance for P0455
Check your VIN first. A service bulletin applies only to the vehicles it lists, often only certain model years or engines. It doesn’t mean every car of that model has the problem, or that yours does. Ask a dealer to run your VIN for open bulletins and recalls before you buy parts.
- GM 21-NA-124 (May 2021): a diagnostic tip for P0442 and P0455 on GM gasoline engines from 2000 to 2021. It lists P0455 causes as “an unseated tube connection, a damaged tube, a stuck opened canister vent valve or a stuck closed purge valve,” and recommends smoke testing under both pressure and vacuum. Read it on NHTSA.
- Nissan NTB13-097g: one diagnostic path for P0442, P0455 and P0456 on 2012 and newer Nissans. If no leak is found, the cause was a fuel cap that wasn’t secured, so the codes are erased and no parts are replaced. Read it on NHTSA.
How to fix a P0455 code
What you can do yourself
- Check the cap. Is it there, undamaged, clicking when tightened, and the correct part? Check the filler neck for rust or pitting first. Identifix says to fix a pitted neck before buying a cap, because no cap will seal against it.
- Capless filler? Inspect and clean the flap.
- If you replace the cap, use an OEM cap (Identifix).
- Drive normally for several days. The EVAP test usually runs on a cold start with roughly a quarter to three-quarters of a tank (Identifix), so it can take a day or two to rerun. RepairPal says once the system no longer detects the issue, “most codes will disappear on their own.”
- Look under the hood and near the tank for popped or cracked vapor lines.
- Turn the engine off when you refuel (EPA).
- With a scanner, confirm the code and check for related codes, such as P0441, P0446, P0451, P0452 or P0171. Check that the EVAP readiness monitor has run before an inspection.
What a shop does
Per Identifix and GM, a shop commands the vent valve closed and watches tank pressure, tests the vent and purge valves with a hand vacuum pump, runs a smoke test under both pressure and vacuum, and follows make-specific procedures such as Nissan’s NTB13-097g.
Typical fixes
Reseating or replacing the cap (OEM); repairing the filler neck or capless flap; replacing a cracked hose or reconnecting a quick-connect; a vent solenoid; a purge valve (Identifix says replace it rather than clean it); the canister; a tank seal or pressure sensor; or a software update where a bulletin applies. Identifix describes the range as running from a gas cap at the low end to a canister or tank job at the high end. Then let the EVAP monitor finish before an inspection.
A scanner to confirm the code and readiness
A basic OBD2 scanner confirms P0455, shows related codes, and tells you whether the EVAP monitor has run. Commanding the vent and purge valves needs a bidirectional tool, which we haven’t confirmed for these picks, so treat that as shop work. These are the three picks from our best Bluetooth OBD2 scanner guide:
We may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Read our affiliate disclosure.
- Best overall: BlueDriver OBD2 Scanner (Bluetooth). Car and Driver’s Best Bluetooth Scanner in its 2026 test. Its listed features include live data, freeze frame, smog readiness and Mode 6, with no subscription.
Where to buy: Check price at Amazon · Check price at Walmart · Check price at BlueDriver
- For enthusiasts: OBDLink MX+. Works with iOS, Android and Windows, adds MS-CAN and SW-CAN for Ford and GM, and pairs with apps like FORScan. Check the current price at Amazon.
- Budget: Veepeak OBDCheck BLE. A small ELM327 adapter that works with third-party apps. Check the current price at Amazon.
How we built this guide
We did not diagnose any cars for this guide. Mike re-read every source on November 17, 2026: Identifix’s P0455 guide (published October 8, 2026), RepairPal, the federal OBD rule (40 CFR 86.1806-17), the EPA’s OBD brochure, and the manufacturer bulletins on NHTSA linked above.
More in this topic: Car tech start-here guide.
For our full process, see how we choose the gear we recommend.
FAQ
Will P0455 go away on its own after I tighten the cap?
Often, if the cap was the cause. RepairPal says once the system no longer detects the issue, “most codes will disappear on their own.” It can take a few days of driving for the EVAP test to rerun. If the code persists, get it diagnosed.
Is P0455 the purge valve?
It can be, but check the cap and hoses first. GM’s bulletin 21-NA-124 lists a purge valve stuck closed and a vent valve stuck open among the causes, along with unseated or damaged tubes. A shop can test the valves directly.
I replaced the gas cap and still have P0455. What now?
Check that the filler neck isn’t rusted or pitted, look for popped vapor lines, and then get a smoke test. Identifix warns that aftermarket caps with the wrong seal can leak “while looking perfectly fine,” so use an OEM cap.
Can I drive with P0455?
Usually, yes, short term, if you don’t smell fuel. RepairPal rates it “Moderate.” But a strong fuel smell or a visible leak needs immediate attention, Identifix says, because fuel vapor near an ignition source is a fire risk. Don’t keep driving on it.
What’s the difference between P0455 and P0442?
P0455 flags a large leak (or, per GM, a purge blockage), where the system can’t build or hold vacuum. P0442 is a small leak of about 0.040 inch. See our P0442 guide.
Related codes
Engine codes to know: P0420 catalyst efficiency and P0300 random misfire.
Mike is the byline for The Car Gear Guide’s research team. We read independent tests, maker specs and fit guides, then turn them into plain-English buying guides for US drivers. We don’t hand-test the products we recommend. Guides are researched and drafted with AI tools, then fact-checked and edited before they go up.