P0442 Code: EVAP System Small Leak Detected (Gas Cap First)

We may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Read our affiliate disclosure.

Short answer

If you want to read the code yourself, our pick is the BlueDriver OBD2 Scanner. See the BlueDriver OBD2 Scanner at Amazon.

A P0442 code means your car’s evaporative emission (EVAP) system has a small leak. The EVAP system traps gasoline vapor from the fuel tank, and during its self-test, it couldn’t hold vacuum as long as it should.

The short answer: start with the gas cap. Refit it until it clicks, check its rubber seal, and drive normally for several days so the system can retest itself. If the code comes back, a shop smoke test is the reliable next step, rather than guessing at valves. The immediate risk is low, but a strong fuel smell changes that, and in states with OBD emissions testing, a lit check engine light usually means a failed inspection.

Jump to: What it means · Vs. other EVAP codes · Is it safe to drive? · How to fix it · A scanner · FAQ

What does the P0442 code mean?

P0442: Evaporative Emission System Leak Detected (small leak). That’s the wording in public code lists and on RepairPal. GM’s bulletin calls it “Evaporative Emission System Small Leak Detected.” (The original SAE J2012 text is paywalled.)

RepairPal explains that the system “will not hold a specified level of vacuum for a specified amount of time” during its leak test, and the computer sets the code after the vacuum decays too fast “on two successive tests.”

How small is small? P0442 means a small leak, often described as about 0.040 inch (Identifix). P0456 is the very small version, about 0.020 inch, which is the size federal rules require OBD systems to detect (40 CFR 86.1806-17). Exact thresholds vary by manufacturer.

P0442 vs. P0455 vs. P0456 vs. P0457

Code Name What it means
P0456 EVAP leak detected (very small leak) About 0.020 inch, the federal detection threshold
P0442 EVAP leak detected (small leak) About 0.040 inch
P0455 EVAP leak detected (large or “gross” leak) The system can’t build or hold vacuum. GM’s bulletin says “large leak or purge blockage.”
P0457 EVAP leak detected (fuel cap loose/off) Some makes set this code for the cap specifically

For the large-leak version, see our P0455 guide.

Is it safe to drive with a P0442 code?

  • Usually, yes, short term, if there’s no fuel smell or leak. RepairPal rates P0442 “Moderate,” and RepairPal says there’s usually no change in how the car drives. The EPA’s brochure says a steady light is “no cause for panic,” but to “seek attention soon.”
  • The exception is a fuel smell or leak. In its P0455 guide, Identifix says a strong fuel smell or a visible fuel leak needs “immediate attention,” because fuel vapor near an ignition source poses a fire risk. Don’t keep driving on it. If it happens on the road, pull over somewhere safe and turn the engine off: Kia’s fuel-leak recall notice, hosted by NHTSA, says “If fuel smell and/or leakage is detected, immediately TURN OFF your engine, and do not drive your vehicle.” Keep sparks, flames and cigarettes away, and have the car towed for repair.
  • It can fail inspection. In states with OBD emissions testing, a lit check engine light usually means a failed inspection, and a lit light can hide a new problem.

For what solid and flashing lights mean, see check engine light on? what it means and what to do.

Symptoms

  • A check engine light, often the only symptom (Identifix)
  • Possibly trouble refueling or slightly worse fuel economy (Identifix)

What causes a P0442 code?

  1. A loose, damaged or wrong gas cap, including one that doesn’t meet the original spec. RepairPal lists the cap first, and Identifix’s P0455 guide recommends an OEM cap.
  2. A damaged filler neck, or on capless systems, the internal seal or flap (Identifix).
  3. A small crack or hole in an EVAP hose or the charcoal canister.
  4. A vent or purge valve. GM’s bulletin 21-NA-124 says P0442 “can occur from a stuck open purge valve or stuck open canister vent valve,” or from an unsealed system.
  5. A fuel tank seal, tank pressure sensor or leak detection pump. RepairPal notes a seal not installed properly after a fuel pump replacement can leak.

Watch for other EVAP codes. RepairPal says purge or vent codes (P0443, P0446), tank pressure sensor codes (P0451, P0452) or leak detection pump codes can trigger P0442. Fix those first. RepairPal’s list of common misdiagnoses is “Fuel cap, Evaporative Purge Valve, Evaporative Vent Valve,” parts that get replaced when the leak is somewhere else.

Known factory guidance for P0442

Check your VIN first. A service bulletin applies only to the vehicles it lists, often only certain model years or engines. It doesn’t mean every car of that model has the problem, or that yours does. Ask a dealer to run your VIN for open bulletins and recalls before you buy parts.

  • GM PI0979: “MIL Illuminated, DTC P0442 Set – EVAP System Small Leak Canister Vent Solenoid (CVS) Valve Not Sealing Under Vacuum,” on 2012–2013 Buick LaCrosse, Regal and Verano, 2013 Cadillac ATS, 2011–2013 Chevrolet Cruze, 2012–2013 Chevrolet Orlando and 2013 Chevrolet Malibu. The vent solenoid can seal under pressure but leak under vacuum, so a normal smoke test can pass. Read it on NHTSA.
  • GM 21-NA-124 (May 2021): a diagnostic tip for P0442 and P0455 on GM gasoline engines from 2000 to 2021: “Some leaks will only be noticeable under pressure and some only noticeable under vacuum. We recommend checking both ways.” Read it on NHTSA.
  • Nissan NTB13-097g: EVAP leak information for P0442, P0455 and P0456 on 2012 and newer Nissans (per Identifix, it excludes the LEAF and Titan XD diesel). If no leak is found, the cause was a fuel cap that wasn’t secured, so the codes are erased and no parts are replaced. Read it on NHTSA.

How to fix a P0442 code: gas cap first

What you can do yourself

  1. Check the gas cap. Remove it and refit it until it clicks. Inspect the rubber O-ring and the filler neck’s sealing surface for corrosion or damage. Replace a cap that doesn’t seal, ideally with an OEM cap (Identifix’s P0455 guide).
  2. Capless filler? Many Fords use a capless “Easy Fuel” filler. There’s no cap to check, so inspect and clean the flap and its seal. Identifix says on a capless system, “the seal itself is the suspect.”
  3. Drive normally for several days. The EVAP test only runs under certain conditions, usually a cold start with roughly a quarter to three-quarters of a tank (Identifix’s P0455 guide), so it can take a few days to rerun. The EPA says that if the light doesn’t go out after a few short trips, have the car serviced.
  4. Look over the EVAP hoses you can reach, under the hood and near the tank, for cracks or popped fittings.
  5. Turn the engine off when you refuel (EPA).
  6. With a scanner, check for other EVAP codes, and confirm the EVAP readiness monitor has run before an inspection.

What a shop does

A shop runs an EVAP smoke test, under both pressure and vacuum where possible, as GM recommends. It can command the purge and vent valves with a bidirectional scan tool, check the tank pressure sensor, and follow make-specific procedures like GM PI0979 and Nissan NTB13-097g. Identifix says that without a smoke machine, you’re better off going to a shop than guessing at parts.

Typical fixes

An OEM gas cap or capless seal; an EVAP hose, clamp or O-ring; a vent solenoid (common on GM, per PI0979); a purge valve; the canister; a tank seal; or a pressure sensor. Then let the EVAP monitor finish before your inspection. Costs range widely depending on which part it turns out to be.

A scanner to confirm the code and readiness

A basic OBD2 scanner confirms P0442, shows any other EVAP codes, and tells you whether the EVAP monitor has run. Commanding the purge and vent valves needs a bidirectional tool, which we haven’t confirmed for these picks, so treat that as shop work. These are the three picks from our best Bluetooth OBD2 scanner guide:

We may earn a commission when you buy through links on this site, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Read our affiliate disclosure.

  • Best overall: BlueDriver OBD2 Scanner (Bluetooth). Car and Driver’s Best Bluetooth Scanner in its 2026 test. Its listed features include live data, freeze frame, smog readiness and Mode 6, with no subscription.

    Where to buy: Check price at Amazon · Check price at Walmart · Check price at BlueDriver

  • For enthusiasts: OBDLink MX+. Works with iOS, Android and Windows, adds MS-CAN and SW-CAN for Ford and GM, and pairs with apps like FORScan. Check the current price at Amazon.
  • Budget: Veepeak OBDCheck BLE. A small ELM327 adapter that works with third-party apps. Check the current price at Amazon.

How we built this guide

We did not diagnose any cars for this guide. Mike re-read every source on November 17, 2026: RepairPal, Identifix’s P0442 guide (updated October 21, 2026) and its P0455 guide, the federal OBD rule (40 CFR 86.1806-17), the EPA’s OBD brochure, and the manufacturer bulletins on NHTSA linked above.

More in this topic: Car tech start-here guide.

For our full process, see how we choose the gear we recommend.

FAQ

Will tightening the gas cap clear P0442?

It can, if the cap was the problem. The light goes off once the EVAP monitor reruns and passes, which can take several days of normal driving. If it doesn’t go out after a few trips, the EPA says to have the car serviced.

I replaced the gas cap and still have P0442. What now?

Check the filler neck’s sealing surface, look over the hoses you can reach, and then get a smoke test. In one r/ToyotaTacoma thread (an unconfirmed owner account), the code stayed after a new cap, and a shop smoke test traced the leak to the gas-cap area.

The smoke test found nothing. Why do I still have P0442?

Some leaks only show under vacuum. GM’s PI0979 bulletin covers vent solenoids that seal under pressure but leak under vacuum, and GM’s 21-NA-124 recommends testing both ways. In one r/cruze thread (an unconfirmed owner account), a new cap and purge valve didn’t clear the code, and a smoke test showed smoke coming from above the charcoal canister.

What’s the difference between P0442 and P0455?

P0442 is a small leak (about 0.040 inch); P0455 is a large leak, where the system can’t build or hold vacuum at all. See our P0455 guide.

Can I drive with P0442?

Usually, yes, short term, if you don’t smell fuel. RepairPal rates it “Moderate.” A strong fuel smell or a visible leak is different: Identifix says it needs immediate attention because fuel vapor near an ignition source is a fire risk, so don’t keep driving on it. Fix the code before an emissions inspection.

Related codes

Engine codes to know: P0420 catalyst efficiency, P0300 random misfire and P0171 system too lean.

Leave a Comment